高周波高频机械的正确操作顺序应该是怎样的呢？很多客户朋友会经常问到这个问题,尤其是高周波机械操作员工,下面我将简单介绍高周波高频机械在使用过程中的正确操作顺序。
What should be the correct operation sequence of high frequency and high frequency machinery? A lot of customer friends will often ask this question, especially the high frequency mechanical operation staff, below I will briefly introduce the correct operation sequence of high frequency and high frequency machinery in the process of using.
一、 在高周波高频机械使用之前,先接通三相AC380V电源,并打开总开关,再打开高周波机台侧边控制箱上的电源开关,这里一定要注意,高周(高频0开关暂时需要关闭,然后打开高周波机加热系统电源开关,真空管和热模就开始预热了。
First, before the high frequency machines, first connected three-phase AC380V power supply, and open the switch, and then open the high frequency machine side control power switch box, here we must note that the high frequency 0 weeks (switch requires temporary closed, then open the heating system of high frequency power switch, vacuum tube and heat die start preheat.
二、 在高周波机的下模辅助粘贴上绝缘材料,一般推荐使用高温布,高周波机上极端装上上模,按下高周波机试模开关,并且调试上下模接合位置保持水平,如果高周波模局具上下模接合不良,就移动下模,如果水平不合,就调较上模的四支柱子,直到高周波高频模具调至水平状态为止。
Two, in the lower die auxiliary sticking high frequency machine on the insulating material, is generally recommended to use high temperature cloth, high frequency machine installed on the extreme mode, press the high frequency machine test mode switch, and the adjustment of the upper and lower die bonding position to maintain high level, if Zhou Bomo Council with the upper and lower die bonding, moving die, if the level is appropriate, adjust the four pillars of the upper mold, high frequency mold until transferred to the level of state.
三、 高频模具调至水平后,调节高周波控制台相关时间控制器(高周波机机头下降时间,熔接时间,定型时间),高周波机头下降时间即高周波模具上模运行到压紧下模的时间.熔接时间.即高周波输出时间,定型时间,即固化时间,相关时间需灵活应用,并无固定值数,需要注意的是,双头脚踏机型,只有高周熔接时间。
Three, high frequency mould to the horizontal regulation after high frequency related time controller console (high frequency machine down time, welding time, setting time), high frequency head fall time is high frequency of mould operation to compress the time under the mold. The welding time. High cycle wave output time, setting time. The curing time, the correlation time of flexible application, no fixed value of the number, note, double foot models, only a high cycle welding time.
四、 高周波高频机械第一次调模,需将高周波机同调调谐调的间距调到最大。
Four, the high frequency high frequency machine first adjust the mold, need to tune the tune of the high frequency machine tune spacing to the maximum.
五、 当上操作完成,且温度也达到所需时,这个时候可以把高周开关打上,开始操作测试,熔接热合焊接所需加工件。
Five, when the operation is completed, and the temperature also reaches the required, at this time you can turn on the high cycle switch, start operation test, welding heat sealing welding processing parts.
六、 高周波测试时,如果高频焊接的效果不理想.需将同调器慢慢加上去,注视屏流表（不同高周波机型该表的值不同,请参考说明书或者明白技术的人员帮助）,检查产品.如果焊接效果仍然不理想,就把同调器加一点或减一点,直至达到要求。
Six, high frequency test, if the high-frequency welding effect is not ideal. The adjuster will need to slowly add up, monitor screen flow table (different high frequency models with different values of the table, please refer to the instruction manual or technical staff to help understand, check the product). If the welding effect is still not ideal, put the same adjuster plus a little or a little less, until the meet the requirements.