高频机打火不仅损坏模具和产品，是很多厂家头痛的事情。青岛平顺和高周波对这一现象做出完美的解决方案。
High frequency machine fire not only damage the mold and product, it is a headache for many manufacturers. Qingdao's smooth and high - frequency waves make a perfect solution to this phenomenon.
高频热合机打火现象分析
Analysis of fire phenomenon of high frequency heat combination machine
1、模具水平调整的不够，容易导致打火。
1, the level of the mold adjustment is not enough, easy to lead to fire.
2、模具打火后没有采用适当的办法处理高频模具跳火留下的灰尘和黑点。
2, the mold did not use appropriate methods to deal with the dust and black spots left by the high frequency die after fire.
3、在热合过程中高频电流调至的过大，造成使模具吃火现象。
3, high frequency current in the process of heat fusion is too large, causing the mold to eat fire.
4、模具上模还没有完全和下模接触就开始发射高频机电流。
4, the mold on the die has not fully contact with the lower die start to launch the high frequency machine current.
5、高频模具表面的结缘材料没有得到适当的处理
5. The bonding material on the surface of the high frequency die has not been properly treated
6、长时间工作没有清洁，导致灰尘堆积。从而导致工作时灰尘引起打火现象。
6, long time work is not clean, resulting in dust accumulation. It causes the dust to cause fire in the work.
解决高频热合机打火现象方法
A method to solve the fire phenomenon of high frequency heat combination machine
1、高频模具水平调节一定需要调节水平
1. The level adjustment of the high frequency mould must be adjusted.
2、高频模具出现打火现象要用干净的抹布，加上酒精、汽油、甲苯等擦拭模具机器的灰尘。
2, high frequency mold fire phenomenon to use clean cloth, plus alcohol, gasoline, toluene and so on to wipe the dust of the mold machine.
3、每次调试新的模具，电流都应该调整至回0.2A。利用同调器慢慢的把电流调至适合的电流热合。
3. Every time a new mold is debugged, the current should be adjusted to 0.2A. Use the homology to slowly adjust the current to the suitable current heat.
4、高频模具下面必须采用一定的结缘材料。有效地防止高频再次击穿所需要的焊接产品
4. A certain bonding material must be used under the high frequency mold. Welding products needed to effectively prevent high frequency re breakdown
5、电容片在调节过程中不要调节的过于猛烈，应当慢慢的调试相应的范围，电容片在生产过程中边缘出现打火
5, the capacitor chip should not be adjusted too fiercely during the adjustment process, it should be slowly debugged the corresponding range, and the capacitor sheet is igniting on the edge of production.
象，可能是电容片的边缘没有处理干净又铝板毛刺。需要用砂纸处理打磨光滑。
It may be that the edge of the capacitor is not treated with clean and aluminum burrs. It needs to be smoothed with sand paper.
6、振荡桶在生产过程中出现的打火现象主要有电容片，高压管座等跳火。处理方式和电容调节片一样。
6, the oscillation barrel ignition phenomenon appears in the production process of capacitor plate, high pressure tube support jump. The processing method is the same as the capacitance regulator.